| | |  | Search by Manufacturer | Home » » Bosch TS1002 Table Saw Rear Outfeed Support Extension | | | | | | | Description: | | Table saw rear outfeed support extension. Extends 18-inches and stores flush to table; extends working depth of Bosch 4000 10-inch table saw. Hardened metal construction; aluminum mounts. Includes 1 table saw extension; table saw not included. 1-year warranty | | | Features: | |
• Table saw rear outfeed support extension
• Extends 18-inches and stores flush to table; extends working depth of Bosch 4000 10-inch table saw
• Hardened metal construction; aluminum mounts
• Includes 1 table saw extension; table saw not included
• 1-year warranty
| | | Product Details: | | | Product Length:
| 0.0 inches | | Product Width:
| 0.0 inches | | Product Height:
| 0.0 inches | | Product Weight:
| 0.0 pounds | | Package Length:
| 29.7 inches | | Package Width:
| 5.2 inches | | Package Height:
| 1.6 inches | | Package Weight:
| 8.6 pounds | | Average Customer Rating:
|  based on 57 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 57 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
104 of 105 found the following review helpful:
 Video review to clear up conflicting informationSep 25, 2009
By Samuel Curren
"TelegramSam"
Watch Video Here: http://www.amazon.com/review/RYJA6ZOVHFCLD There seem to be plenty of conflicting reviews on both the left side extension and the outfeed extension, and I've made this video to clear them up. Issues cleared up:
- The front bar for the left side extension is short enough to not hit the red lever for the right side extension.
- Both left side extension and outfeed extension come with a stop knob for securing the extensions either open or closed.
- Both extensions sag just a little, which I fixed by placing a washer (approx 0.043 in thick) between the brace and the tablesaw for the _back_ bolt on each bracket. This modification brought it very close to level, for just over $2 in washers at my local big box hardware store.
I do say a few odd words here and there in the video (quarters when I meant washers, etc.) But I'm sure you can figure it out.
Overall review: These were what I expected, fit my 4100 series Bosch worksite table saw, and were easy to install following the included instructions.
50 of 51 found the following review helpful:
 outfeed supportJan 30, 2002
The outfeed support is a handy thing to have on a table saw. The only problem that I have encountered in useing it is that flexible materials like thin plywood tend to flex between the saw and the outfeed support and hit the support instead of going on top of it. This problem can be fixed by using a peice of scrap as a 'brige' to help the material make it onto the suport.
32 of 32 found the following review helpful:
 mike in maineOct 22, 2007
By Michael R. Golden
After reading some of the poor reviews for this product I had some reservations.When I unpacked and assembled the extention I soon discovered the problems others had described.1st the miter guide slots don't align with the notches in the extention.2nd the sliding rails are too far apart, one owner had elongated the mounting holes to address this.The actual problem is in the illustrations in the instructions! The pictures of the model 4000 saw and the 4001 saw are reversed.Simply mount one bracket facing outward[the one with the lock knob]and the other facing inward,as pictured for the model 4001,and the extention fits and operates smoothly! Perhaps BOSCH should correct the instructions instead of agreeing they had made a manufacturing error to appease a dissatisfied customer. I hope this helps others who encounter this problem.
19 of 19 found the following review helpful:
Must have for large piecesJan 09, 2007
By D. Ward
Bolts on easily. Supports well after the cross bar is redrilled to align the support with the table. It is 1/2" low to the table when at full extension. Only one thumbscrew included for locking position but both brackets are drilled and tapped for it.
Must be careful when cutting 4x8 sheets as the saw can tip with this support at full extension and the board hanging off it.
5 of 5 found the following review helpful:
great value- must haveMay 19, 2006
By rama
Not sure why the outfeed is almost 1/2 the price of the left side support, but its you're going to drop the money for the saw, this is a must have accessory. Its solidly built and exudes quality, just as all Bosch tools do.
I didn't have a problem with the retaining clips being too large, as an earlier reviewer noted. I guess Bosch caught this mixup and remedied it.
See all 57 customer reviews on Amazon.com
| | |
|
