| | |  | Search by Manufacturer | Home » » HTC 10A-L Brett-Guard Table Saw Guard | | | | | | | Description: | | The HTC Brett-Guard Table Saw Guard is designed to overcome the objection "we can't guard that operation." The saw guard is exceptionally effective and easy to use, and provides excellent protection in a package ideally suited to 10-inch contractor style saws (it also works on cabinet saws). Its fully adjustable inverted box-type transparent shield provides safety while performing virtually any cutting operation. When properly adjusted, the adjustable fixed barrier guard will not ride up, or climb over the work piece or, more importantly, your fingers, providing excellent protection from the blade. The clear shield is firmly suspended over your work in either a cantilever or tabletop mount, and the anti-kickback mechanism can be retracted for working with soft materials or veneers. Each guard is OSHA and ANSI compliant and also includes a splitter. | | | Features: | |
• Saw guard with excellent protection for 10-inch contractor style saws
• Fully adjustable inverted box-type transparent shield
• Adjustable fixed barrier guard delivers excellent protection from blade
• OSHA and ANSI compliant
| | | Product Details: | | | Package Length:
| 26.3 inches | | Package Width:
| 15.2 inches | | Package Height:
| 7.3 inches | | Package Weight:
| 19.8 pounds | | Average Customer Rating:
|  based on 9 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 9 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
20 of 20 found the following review helpful:
 Much better than stock safety guardsOct 11, 2006
By D. Hankins
I first saw this product in the "Mastering Your Table Saw" DVD (which is a great DVD). If you get this DVD, you'll see it being used all the time. I purchased it for my Dewalt DW746 table saw.
The guard is clear so you can see the cutting action, and easily and quickly slides in and out on two steel support rods. Once you have its mounting plate attached to your table, you can remove the entire guard assembly with the twist of a knob. Very nice.
I see so many people using their saws without any guard at all (mostly because the stock guards are so bad). That's just not an option for me, because I know someday I'll make a mistake. Hopefully, the HTC guard system will keep me safe when that happens.
Note: If you purchase the left hand mount version and have a deep left hand extension table (like the Bench Dog router table), you might need the 30" support rods (my unit came with the 24" rods, which are fine for most applications). If you do need the longer rods, contact HTC directly [...]. They swapped my 24" rods out for 30" rods. Awesome customer service.
15 of 15 found the following review helpful:
Goot tool and easy to use!Oct 24, 2007
By Vic K
After replacing the Powermatic 66 standard blade guard and anti-kick back with an after market Biesemeyer T-Square Anti-Kickback Snap-In Spreader, I quickly realized that I needed some additional protection from the blade and the wood chips flying in my face. After doing some research I came up with 3 possible options:1) Biesemeyer T-Square Table Saw BladeGuard System, 2) HTC 10A-M50 Brett-Guard Table Saw Guard or 3) HTC 10A-L Brett-Guard Table Saw Guard. As it happens I have a router table on the right side of my saw which eliminated the first 2 options. I went with HTC 10A-L Brett-Guard Table Saw Guard which is mounted on the left of the blade screwed to the extension wing.
Here are some of the good points:
1) Easy to install once you figure out the directions, which were not very clear.
2) Easy to mount and unmount from the table.
3) Easy to use during cuts
4) Nice suction hole on top for dust extraction (this option is the model with a "P" in the model number such as HTC 10A-LP<<<
5) No more dust/chips in my face
6) Hands are forced to stay clear of blade
Not so good points of the blade guard and installation:
1) Instructions not very clear even after 3 readings
2) Missing parts (screws to mount dust cover to bars and screws to mount to saw extension)
3) Needed to file the holes in the mounting base plate to receive the positioning pins, because the pins were slightly out of alignment.
In summary, the HTC 10A-LP Brett-Guard Table Saw Guard is a very good product that will keep your fingers safe and saw dust and chips out of your face. Instructions could be better, but if you spend some time with them you will figure it out. Finally make sure you have all the parts, before you start to assemble, otherwise you will be making an unscheduled trip to the home center.
11 of 11 found the following review helpful:
Worth the hassle so farJan 20, 2007
By Pete Bunyan
I bought this guard after experiencing a kickback on my 1.5 HP Delta contractors saw. I did a lot of research, and decided that the 10A-L was what I wanted, on the gamble that I could make it fit my set up. It's OSHA certified, and easy to remove and reinstall--just a turn of the knob, and maybe a little loosening and retightening of the nut that governs the fit of the housing to the mounting plate.
I read the other review here regarding compatibility with the Benchdog ProMax table, which I have on the left side of my saw. When I got the guard, I set to work on installing it. It was a little bit more work than I'd hoped, but I'm glad for the experience, I guess. Part of it was my being a novice, part of it was HTC.
Based on the only review here right now, I sent an email to HTC asking for the 30" rods, instead of the 24" rods, in order to fit the ProMax. I got a confused response the next day asking what I intended to use the guard for. I sent a very clear reply (with links to the Benchdog Promax product page), and got no response. Perhaps this was because it was the holidays.
I then called, and got a better response, but not perfect. I asked for the 30" rods and the thin kerf splitter. I got the rods in the mail three days later, which was great, but no splitter. I called again, and got the best response to date (this time they gave me a ticket #) and the thin kerf splitter is supposedly on the way.
I needed to drill and tap the holes to attach the guard to the cast iron promax. I had never done that before, but it's a piece of cake. Don't use cutting oil, cast iron is self-lubricating. I used a center punch as a first step with no problems (some web-based statements advise against center punching cast iron). Start with a small drill bit, like 1/8", and work your way up slowly. It drills very easily. Tap and drill tables are all over the web, so it's easy to find what size drill and tap bits you need. Make sure you get both the diameter and the thread count per inch right on the tap drill.
The threads for one of the rod-tightening knobs were not clear, so I had to get a tap for that as well. Easy to fix.
Also, I either lost four screws or they were missing in the package. I had everything else, and can't see how I would lose all four screws, so I think they were omitted.
All the same, I assume my experience was probably worse than average. The parts are rock solid. There's a smidge of give in the guard, as any angle on the end of a 30" rod will show, but the guard is great peace of mind, and is doing the job. It's a great feeling knowing that it will be hard to stick my hand in the blade, no matter what stupid thing I may do.
5 of 5 found the following review helpful:
A SAFETY MUSTMar 16, 2007
By John W. Arnold
THE BRETT GUARD WAS INEXPENSIVE AND EASY TO INSTALL. IT PROVIDES TWO
ESSENTIALS FOR TABLE SAW SAFETY. 1. YOU CAN EASILY MOVE IT OUT OF THE WAY FOR MEASUREMENTS AND 2. EASILY MOVE IT OVER THE BLADE TO PROTECT YOUR FINGERS FROM BEING INJURED. A MUST FOR HOME SHOP WORK.
3 of 3 found the following review helpful:
 good for a blade guard, poor wood splitter, priceyDec 28, 2008
By Thomas W. Nix
"woodhead"
The guard is a great safety device that protects you from the blade but is not hard to remove,raise or lower.
It stands head and shoulders above a stock blade guard.
The anti kickback device is a bit lame with only two points to hold down the workpiece.
You will need to drill holes in your saw table to mount the blade guard's raising and lowering device.
I ordered a thin kerf splitter that cost over $20. A rip off.
I ended up building my own splitter from hard wood.
The guard is pricey at ~$200.
Overall, the guard (even with it's shortcomings) is an excellent safety device.
See all 9 customer reviews on Amazon.com
| | |
|
