| | |  | HTC | Home » » » HTC HJTS-761 Mobile Base For Jet JWTS-10JF Table Saw | | | | | | | Description: | | Accessory for JWTS-10JF. Increase your work space by mounting your machines on HTC mobile machine bases. Gain floor space by positioning machine location to suit your needs, or store machines not in use. Most HTC mobile bases have two rigid-type wheels and one swivel wheel arranged to raise your machine by only 3/4-inch off the floor. Standard easy-set brake knobs on the two rigid wheels provide positive control without use of the controls. Constructed of heavy-gauge steel; full-welded for strength and finished appearance. | | | Features: | |
• Fits JWTS-10JF table saw
• Two rigid wheels, one swivel wheel
• Raises machine 3/4-inch off floor
• Brake knobs to set brake on the two rigid wheels
• Heavy gauge steel, full welded for strength and finished appearance
| | | Product Details: | | | Package Length:
| 32.7 inches | | Package Width:
| 31.5 inches | | Package Height:
| 3.3 inches | | Package Weight:
| 21.8 pounds | | Average Customer Rating:
|  based on 5 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 5 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
8 of 9 found the following review helpful:
 Needs better wheelsSep 12, 2001
By Michael L. Jones
I thought I was getting an item with mobile casters but I did not read the description well enough.This item has one caster wheel and two stationary wheels that you have to stop, bend over and tighten a hand bolt to lock. Moving the item around is easy if you have a lot of mobility room but if you have that much room...you don't need the stand. Save your money and look fo a stand with at least 3 mobile wheels and a lift/lower locking type mechanism. Too much trouble to return so I'm going to keep it and eventually put something less needed when I get my permanent shop. Wouldn't buy again and will probably not buy HTC products either.
4 of 4 found the following review helpful:
This could be dangerous!Jul 07, 2002
By Cecil Arnold
"ctarnold3"
This was the third moble base I bought for Jet equipment and while I consider the other two (for a band saw and jointer) as really good values, the one for the 30" fence cabinet saw is a hazard. After the saw was delivered I put the base together, a simple opertation, then slid the saw off the pallet and on (or should I say in) to the base. I continued to assemble the saw, alligning, etc, until everything was as good as it gets. Finally it is time to move the saw to its more less perminent home. IT ALMOST TIPPED OVER. Upon examination I could see the reason. The swivel wheel was on the side opposite the motor and table extension. This put the two other wheels near the CG for the unit so any movement tended to tilt the entire unit over almost causing 500 pounds of brand new saw, etc. to tumble. Perhaps I would rate this base higher if I had not been forced to rotate the saw 180 degrees in the base by myself, a nerve wracking task. Once it was turned it demonstrated more stability, but not as much as I think this unit should have. Of the three bases I now have I wish one was the Shop Fox.
3 of 3 found the following review helpful:
 Like gliding on ice, deadly ice.Aug 02, 2002
By elder
This mobile base went together in just five minutes. The steel and wheels are all of good quality material. Caution! When I was cutting a 24" X 48" X 5/8"piece of plywood, the tablesaw started to tip due to only one wheel at one end. This almost cost me severe injury to the face as the blade was still running. Talking to techs at HTC, they tell me I would be better off with the "four wheel" mobile base for tablesaws. This stand is being returned and I am buying the HTC 2000 as recommended by the HTC tech team. The one star is for the quality of this product, not safety.
2 of 2 found the following review helpful:
 HTC Mobile Base far exceeds my expectations. The one to get!Apr 16, 2002
I looked at lots of mobile bases before buying this one, then a friend said "have you seen the HTC one? they are the best!". Being that he was an avid wood worker I took his advice and am glad I did. HTC balances mobility and safety for a truly sturdy unit. The base unit is welded (not assembled at home like some mobile bases) and is VERY well made. All three wheels have wheel locks on them. The assembly (basically putting on the wheels), was simple and the unit looks great! The only hard part is putting the saw in the base, I finally decided two people would make this task much easier. If you don't need true four way mobility (an I am unaware of a base that provides this) this mobile base is the one to buy.
HTC HJTS=761 Mobile BaseJul 11, 2002
By Jackie Sue Thompson
Being a owner of a table saw, I know how cluttered your work area can get. With this mobile table, you can take the saw to the trouble instead of the trouble comeing to the saw.
| | |
|
