| | |  | Proxxon | Home » » » Proxxon 28132 Machine Vise MS 4 | | | | | | | Description: | | Proxxon machine vise MS4 for use with micromot drill stand MB140/S number 28606 and bench drill machine TBM115, number 38128. Fits perfectly TBM115 drill machine and MB140/S drill stand. Also welcome helper on every work bench. Quick and easy to install, made of die cast zinc with three machined sides. Jaws are 2-Inch (50mm) wide and 25/64-Inch (10mm high maximum clampined width is 1-11/32-Inch (34mm) | | | Features: | |
• Has horizontal and vertical V-slots for holding round work pieces
• The top with a cast-in hole is optimal for supporting small and fine parts when drilling
| | | Product Details: | | | Package Length:
| 6.9 inches | | Package Width:
| 2.4 inches | | Package Height:
| 0.9 inches | | Package Weight:
| 0.85 pounds | | Average Customer Rating:
|  based on 7 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 7 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
8 of 8 found the following review helpful:
 ReviewMay 30, 2010
By Hector D. Iglesias
If you are used to quality, well, this is junk. It'll work, mind you, but there is no precision anywhere near this vise, and that is a pity because the bench drill it fits is a nice piece of machinery with tight tolerances and rather accurate. I wouldn't mind paying double for a better quality vise, but none is available to fit the drill press. I've seen Chinese made vises MUCH better than this vise, but they are not designed for Proxxon drill presses, so go ahead and buy one, it is better than nothing.
6 of 7 found the following review helpful:
Not a precision vise...Now, Made in Taiwan..Apr 11, 2010
By Happy Shopper
It's an O.K. Vise for crude or free hand drilling and other craft work.
This vise is a knock off of the Japanese made one offered by Micro Mark. Theirs is aluminum and both have the tendency of the movable jaw to rise when tightened. This Proxxon vize is made of Zamak zinc alloy.
The description says that this vise will work with the MF70 mill and with their X-Y positioning table. Yes, but the results will be disappointing.
Thier 24260 solid steel machine vises are much better. I have one that I an satisfied with and have been using for 6 years. I just ordered two more. I hope they are still made in Germany.
The hold down slots using M6x1 hex headed screws and using a 10mm open end wrench is very arkward. I drilled a couple of 1/4 inch holes right above the screw position trough the bottom jaw surface of the vise and used 10-32 socket headed set screws. The steel is not hardened and any high speed steel drill bit will work. This allows me to use 10-32 square nuts with my Proxxon MF70 mill, standard T-nuts with my Taig Micro-Mill, standard T-nuts with my Sherline mill, any T-nut supplied by A2Z-CNC with any other mini or micro mill.
2 of 2 found the following review helpful:
 Works very well with my Proxxon mini drill pressJan 15, 2011
By Paul M. Norman
"Luthier, etc."
This nifty little vise works superbly well with my Proxxon micro drill press. It clamps easily to the bed and provides precision x/y location when drilling extremely small parts.
1 of 1 found the following review helpful:
Just OKJan 09, 2011
By kwb
It works OK, but it doesn't feel like a Proxxon product with this much slop. Hey Proxxon, can't you make a higher precision version for more $$$, like 40 or 50 USD?
Also, can't you make a steel version for (even) more $$$? Zinc is simply not hard enough to be abused, and every vise is eventually abused at some stage.
For the money it's worth itDec 12, 2011
By amzdm78
I know its not exactly a solid precise piece of equipment but it does a decent enough job and for the price no complaints ! Just buy it
See all 7 customer reviews on Amazon.com
| | |
|
